Bio Bidet seat lineup compared: BB-1000 vs BB-2000 vs SlimEdge

Which Bio Bidet to buy, and for whom

Buy the Bio Bidet BB-2000 if you want warm water that doesn’t run out during a long wash. Its hybrid heating system is rated at 1400W on 120V, and the documented flow is up to 0.7 L/min (0.185 GPM) for both the rear and front wash. It replaces your toilet seat, needs a grounded GFCI outlet within reach of its 4-foot cord, and comes in elongated and round (BB-2000R) versions.

Get Bio Bidet BB-2000

Buy the Bio Bidet BB-1000 if you want a full electric seat but don’t need endless warm water. It heats a tank reservoir, so a long wash can use up the warm supply, and the manual says to let the water reheat afterwards. The manual gives its rated power consumption as 660W on North American 120V, well under the BB-2000. You get the same kind of package: a wireless remote, a heated seat, a 3-minute warm air dryer and a deodorizer.

Get Bio Bidet BB-1000

Buy the Bio Bidet SlimEdge if you have no outlet near the toilet or just want to try a bidet cheaply. It isn’t a seat. It’s a non-electric attachment that sits between the bowl and the seat you already have, it sprays at ambient (cold supply) temperature, and one side knob controls water pressure for its two retractable nozzles.

Get Bio Bidet SlimEdge

Water heating: tank, hybrid, or none

The biggest difference between these three is where the warm water comes from. The BB-1000 keeps a small tank of heated water inside the seat. That means the first spray is never a cold shock, but the warm supply is limited. When the tank runs low, the water cools until the heater refills it. Because the tank holds water, the manual tells you to drain it if the seat will sit unused for 14 days or longer. You do that by holding the drain button after shutting off the supply valve.

The BB-2000 uses hybrid heating: a small reservoir backed by an inline heater, so warm water keeps coming for as long as the wash runs. That’s why its 1400W rating is more than twice the BB-1000’s 660W. You can set both water and seat temperature through preset levels (Off, Low, Medium, High) shown by coloured indicator lights.

The SlimEdge has no heater. Its water temperature is your cold supply line’s temperature, which in winter in a northern climate can be much colder than room temperature. If cold water is a dealbreaker, no setting on an attachment will change that. Only a powered seat will.

Seat profile and toilet fit

Both electric seats replace your current seat, so bowl shape decides the size. Measure from the centre of the two seat-bolt holes to the front edge of the bowl. Roughly 16.5 in means round, and roughly 18.5 in means elongated. The BB-2000 comes as an elongated model and as the BB-2000R for round bowls, and the BB-1000 is also sold in both shapes. Check the suffix on the listing against your measurement before you order.

Bio Bidet says the BB-1000 fits all standard two-piece toilets and most modern one-piece toilets. That includes flat bowls and French-curve bowls with at least 2 in of clearance behind the bolt holes. It warns that it may not fit toilets with extreme curvature or a control tank built into the back. The seat’s rear housing needs a flat area to sit on, so a sculpted one-piece bowl is the most common reason it won’t fit.

The SlimEdge keeps your existing seat. Its plate goes under the seat’s hinge bolts, and its stated dimensions are 17 in wide, 7.28 in deep and 3.4 in high, including the side knob housing. Before you buy, check that your seat’s bumpers still rest on the bowl once the plate is underneath. Also check that the knob side has room next to the tank or a wall.

Controls: remote and side panel vs one knob

The BB-1000 comes with a wireless remote, a wall holder and two AAA batteries. It also has a simple panel on the seat with Stop, Posterior Wash and Feminine Wash buttons, so you can still wash if the remote’s batteries die. Wash pressure, water and seat temperature, and dryer temperature are all adjusted with High and Low buttons. The deodorizer has 4 levels, set by pressing Stop and Water together. A seat sensor stops the wash from running unless someone is sitting on the seat.

The BB-2000 adds side controls and a night light, and its remote works the same way: Stop, rear wash, front wash, a Massage button for a pulsating spray, and a 3-minute warm air dryer. An automatic massage setting pulses the spray on its own. You turn it off by holding the button for 3 seconds until you hear two beeps.

The SlimEdge has a single comfort-grip dial on the side. Turning it chooses the posterior or feminine nozzle and sets how hard the water sprays. There’s no stop button and nothing to program. Turning the dial back to its off position closes the valve.

Power and plumbing to check before ordering

Both electric seats must plug into a grounded GFCI outlet. The North American models are 120V, 60Hz, and the BB-2000’s cord is 4 feet long. Measure from the toilet’s rear corner to the nearest outlet. Bio Bidet’s manuals don’t allow extension cords for these seats, so a missing outlet means hiring an electrician before installation.

All three connect to the toilet’s cold supply with a T-adapter that fits between the shut-off valve hose and the tank’s fill valve. The BB-2000 lists a working inlet pressure of 0.04 to 0.74 MPa (about 6 to 107 psi). Very old homes on low pressure, or homes where pressure runs high, should check theirs with a gauge on the supply line. Pressure above the listed range strains the T-adapter seals and the seat’s internal valves.

Upkeep and common failure points

The BB-1000 manual says to use only carbon or iodine inline water filters. Any other filter type voids the warranty, so check the filter’s media before adding one to the supply line. The deodorizer cartridge needs replacing over time, and the manual explains how to remove the seat from its mounting plate for cleaning.

If the BB-2000’s indicator lights start flashing, the manual says to unplug the power cord for 30 seconds and plug it back in. If the problem continues, it lists phone support at 847.458.2334. Weak spray on any of the three usually traces back to a partly closed shut-off valve or a clogged inlet filter screen, not to a failed pump or nozzle.

The SlimEdge has no electronics to fail. The parts that wear are the nozzle tips and the metal inlet fittings, so check the inlet and T-adapter for drips during the first few days after installing it.

FAQ

Is the BB-2000 available for round toilets?

Yes. The round version is sold as the BB-2000R, and the standard BB-2000 is elongated. Measure from the seat-bolt holes to the front of the bowl: about 16.5 in is round and about 18.5 in is elongated.

Can I use the BB-1000 or BB-2000 without an outlet near the toilet?

No. Both need a grounded GFCI 120V outlet, and the BB-2000’s cord is 4 feet long. If there’s no outlet within reach, the non-electric SlimEdge is the Bio Bidet option that works without power.

Why does the BB-1000’s warm water turn cool during a long wash?

The BB-1000 heats a tank reservoir, so a long wash can use up the warm water faster than the heater refills it. The manual tells you to let the water reheat after an extended wash. The BB-2000’s hybrid system adds an inline heater so the warm water doesn’t run out.